Note:  The following documentation is taken directly from the TigerVNC project with a few modifications for clarity when configured for SUSE Linux Enterprise products.  The original documentation can be found here:

https://github.com/TigerVNC/tigervnc/blob/master/unix/vncserver/HOWTO.md

Changes in recent TigerVNC versions

Previous TigerVNC versions had a wrapper script called vncserver. This script could be run as a user manually to start Xvnc process. The usage was quite simple as you just run:

$ vncserver :<display-number> [vncserver options] [Xvnc options]

and that was it. It worked fine for some cases, but far from all. There were issues when users wanted to use it in combination with systemd. Therefore, the implementation had to be changed to comply with SELinux and systemd rules.
 

How to start TigerVNC server

Add a user mapping

With this you can map a user to a particular port. The mapping should be done in /etc/tigervnc/vncserver.users configuration file. It should be pretty straightforward. Once you open the file you will see there are some examples, but basically the mapping is in form:

:<display-number>=user

For example you can have

:1=testuser
:2=vncuser

Be sure to use a different display number for each user.  This is the only entry needed in this file.  The associated port number for the connection is automatically assigned based on the display number plus 5900.  So test will be assigned 5901 and vncuser will be assigned 5902.

Note:  The YaST configuration for "Remote Administration (VNC)" will use :1 (port 5901) as the default display/port for remote access.  If this option is enabled in YaST, do not use the same display/port here in this configuration or there will be a conflict.  Start with :2 or higher.

Configure Xvnc options

To configure Xvnc parameters, you need to go to the same directory where you did the user mapping (/etc/tigervnc/) and open vncserver-config-defaults configuration file. This file is for the default Xvnc configuration and will be applied to every user unless any of the following applies:

• The user has its own configuration in $HOME/.vnc/config.
• The same option with different value is configured in   vncserver-config-mandatory configuration file, which replaces the   default configuration and has even a higher priority than the per-user   configuration. This option is for system administrators when they want   to force particular Xvnc options.

Format of the configuration file is also quite simple as the configuration is in form of:

option=value
option

The following examples are included in /etc/tigervnc/vncserver-config-defaults but are commented out.  Just remove the # to enable the option:

# session=gnome
# securitytypes=vncauth,tlsvnc
# geometry=2000x1200
# localhost   (Note: do not use for standard setup! Will reject all connections not from "localhost")
# alwaysshared

See the following manpage for more details: Xvnc(1).
 

Note:

Set VNC password

You need to set a password for each user in order to be able to start the TigerVNC server. In order to create a password, you just run:

$ vncpasswd

You need to run it as the user who will run the server.

Note:

If you used TigerVNC before with your user and you already created a password, then you have to make sure the $HOME/.vnc folder created by vncpasswd have the correct SELinux context. You either can delete this folder and recreate it again by creating the password one more time, or alternatively you can run:

$ restorecon -RFv /home/<USER>/.vnc
 

Start the TigerVNC server

Finally you can start the server for each user identified in the vncserver.users file by using the systemd service. To do so just run as root:

# systemctl start vncserver@:<display-number>

Or as a normal user using sudo:

$ sudo systemctl start vncserver@:<display-number>

 Be sure to replace <display-number> with the actual display number assigned to the user you are starting the service for.  For example, if I want to start the service for "testuser" from above, I would run as root:

# systemctl start vncserver@:1

This starts a TigerVNC server for user testuser, but it will not survive a reboot.  To make it permanent, enable it with the command:

# systemctl enable vncserver@:1

Repeat the above steps for all users that need access. 

Note:

Limitations

You will not be able to start a TigerVNC server for a user who is already logged into a graphical session. Avoid running the server as the root user as it's not a safe thing to do. While running the server as the root should work in general, it's not recommended to do so and there might be some things which are not working properly.