Use of the x-systemd.automount mount option in /etc/fstab

This document (000020402) is provided subject to the disclaimer at the end of this document.


SUSE Linux Enterprise Server 15
SUSE Linux Enterprise Server 12


Administrators are sometimes confused by systemd's handling of /etc/fstab options "auto" or "noauto" in connection with "x-systemd.automount".


When x-systemd.automount is used, systemd will enable an "automount unit", also known as a automount trap, or a mount point (path) where a file system may later be mounted.  The file system itself is a separate unit (a "mount unit") and will only be mounted if there is a subsequent demand to use that path.

Attempts to alter the above behavior by setting either "auto" or "noauto" will have no effect.

In other words, all of the following combinations of options in /etc/fstab will yield the same result:


NOTE:  A variety of different services or entities started by systemd can insist that something be mounted.  Additionally, any process started during boot can request access to various paths, potentially triggering an automount unit to mount a file system.  Therefore, even if /etc/fstab syntax would give the expectation that a file system won't mount during boot, it may still get mounted during boot for other reasons.

Additional Information

If there is an automount trap set (for example, at the path /mnt/sub1), it can be seen with:

grep auto /proc/mounts
systemd-1 on /mnt/sub1 type autofs (rw,relatime,fd=51,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=24999)

Please note that systemd's automount feature is separate from the method provided by the autofs package, which has been around many years longer.  The method used by the autofs package does not use entries in /etc/fstab.  Instead, it uses /etc/auto.master plus map files.  Either method will result in automount traps of "type autofs" .  Even so, they are two distinct methods.  Either method can be used on SLES 12 and 15, but any given mount point should only be defined by one of the methods.   Technically, a system could have one set of mount points under the control of the autofs package and another set under the control of systemd.  However, to avoid confusion, it is recommended that just one method be used for all automounts on any given system.

For someone not familiar with either method, the systemd method is typically more quickly grasped and implemented.

A notable difference between the default behaviors of x-systemd.automount and the autofs package is:  The autofs package defaults to timing out (umounting) an automount after approximately 10 minutes of idleness.  However, x-systemd.automount defaults to never timing out, which is preferred by many administrators.  Repeatedly umounting and remounting based on idle periods can introduce potential points of failure.

For more information on the timeout settings for each of these, see "man 5 auto.master" (for the autofs package) and "man 5 systemd.automount".


This Support Knowledgebase provides a valuable tool for SUSE customers and parties interested in our products and solutions to acquire information, ideas and learn from one another. Materials are provided for informational, personal or non-commercial use within your organization and are presented "AS IS" WITHOUT WARRANTY OF ANY KIND.

  • Document ID:000020402
  • Creation Date: 01-Oct-2021
  • Modified Date:08-Oct-2021
    • SUSE Linux Enterprise Server

< Back to Support Search

For questions or concerns with the SUSE Knowledgebase please contact: tidfeedback[at]

SUSE Support Forums

Get your questions answered by experienced Sys Ops or interact with other SUSE community experts.

Join Our Community

Support Resources

Learn how to get the most from the technical support you receive with your SUSE Subscription, Premium Support, Academic Program, or Partner Program.

SUSE Customer Support Quick Reference Guide SUSE Technical Support Handbook Update Advisories
Support FAQ

Open an Incident

Open an incident with SUSE Technical Support, manage your subscriptions, download patches, or manage user access.

Go to Customer Center